Hi there,

I have an irrigation system in my garden with 7 zones. The solenoid valves and the irrigation controller are new. Irrigation was already in place when I bought the house, so I don't know where the underground pipes run.

When I open one of the zones, no sprinkler pops up. I don't know if the pipe is clogged or if the sprinklers were removed or just don't work. Digging in my garden is very difficult because the soil is very stony.

Is there any technique, trick or machine that will allow me to track the underground pipe in that area? I would like to rehabilitate it.

Thanks! 

Any comments are welcome.

Regards, 

Hi just installed a sprite 6. I can here zone turn on then immediately turns off but the timer is still running on the app. I can hear the water stop and start in each zone ; the app thinks it's watering but the valve closes. Same for all zones

Thansk 

Wondering how to use the online weather forecast and be able to use that information to turn off the next day scheduled watering. 

I'm checking the rainy days manual and turn on/off the system which is cumbersome! Appreciate letting me know.

I bought a new phone today and am unable to water my lawn and vegetable garden because the app asks for a password, which I have forgotten.

I have tried number of times to get it to open up with a new password and the app still does not go back to normal.

Please call me on my cell phone.  209-482-0316

I would like to be able to get this to work because it is getting hot in California.  It is to be in the 90's tomorrow.

Linda Lundgren

• I have received a new Pixie-Z1 and a hub
• Downloaded the Netro iOS App from the UK app store
• In the App I added the hub connecting through Bluetooth and configuring WiFi access for the hub
• Hub shows constant green light

Why netro don’t have notifications when it’s watering. Begging and end like wother. Orbits b havy and RainMachine 

Hi,

Firstly, I have a Sprite and love it! Easy to install, easy to set up and I'm really impressed with it.

I have a smart water meter so I know exactly how much water each zone uses and I can see that the Netro Sprite's estimate of water used during irrigation is about 75% of the actual usage as reported by my water meter.  This means that I am probably over watering.

Is there an easy way in the app to calibrate the expected flow rate (litres/minute) of a zone's sprinklers such that the smart algorithms deliver closer to the amount of water they think is needed?  Or put it another way, instead of calculating it needs to run a zone for say 10 minutes, they would just run for 7.5 minutes.

I have a delay set on 5 days, I try to change it to reduce to 1 day but the system stay on 5

I have a sprit 6 I just hydro seeded so I have to keep the ground damp. I’m at work away from the house and the app says it didn’t watered in my last 2 programs. I tried to do a manual run and it wouldn’t work. Do I have to be home for it to work?

Hi, is impossible access app netro

Good morning,

I have three Wisperers and a Pixie. I can't install my three Wisperers in the same area as my Pixie. I managed to install Wisperer with my Pixie but the other two. How do I install all Wisperer with my Pixie?

If the Pixie is installed in a different area than the Wisperers, does it all work together to optimize my garden watering?

Apollon16

hello, can you turn off the led on netro sprite?

Please renew the certificate so our app works again..  

Maybe you need to set a reminder around this as this seems to be a reoccurring problem.

The certificate has expired. Please renew it asap as we are not able to access to the app

Please help resolve problems with whisperer moisture sensor. Does it need to be regularly cleaned or something so it will work properly???

Why doesn't sensor moisture percent change after watering grass

Hello everyone. 

Hello everyone.