更多筛选条件

Problem with irrigation time

Daniel Encinas
更新时间 2024-07-12 10:43:36 UTC 
Hello, I have owned a Netro Sprite programmer for several years.

The problem I have is that it programs the phases intelligently and if it indicates that it has to water for 10 minutes. It only waters for about 1 minute but the app shows that it has watered for 10 minutes. The garden is drying out and I don't know what to do.
This happens to me in all irrigation phases. If I program it manually the same thing happens to me. If I try it twice, the second time it takes even less time to water.
I have connected the transformer directly to the phase, bypassing the programmer, and it works correctly.
Reviewing its problems section, I found a similar one in which it says to look at the 24 volt voltage. (which is correct, around 30 volt) and the resistance in ohms of more than 20 (around 30 ohmios). It also says that there the programmer has a recoverable fuse.

What can I do?


Thanks

浏览: 833   回复: 1

Manual watering beta

Lynn johnson
更新时间 2024-07-10 04:17:16 UTC 
话题: Netro App
So I like the idea of being able to manually water when I want especially on really hot days but the battery aftervthe second day dies and never charges more then 10 to 15 percent even in full sun for 10 hours. Would be nice if it charged faster and had a better battery or less drain in that mode.
浏览: 835   回复: 1

Cannot find master solenoid valve

kvschlegel
更新时间 2024-07-06 22:46:35 UTC 
None of the zones are watering when the app says it's watering. I measured each zone when active and each read 28 AC. When testing the resistance, the readings were jumping all over the place for each reading. This is leading me to believe there is an issue with the master solenoid valve. However, there is no wire that connects to the M slot on the controller. Looking around the house for any of the underground boxes, I have not been able to find the master solenoid. Attaching pictures of what I have found. Any help greatly appreciated.
浏览: 975   回复: 2

2 zones must run the same amount of time

Alfonso Olias Sanz
更新时间 2024-07-06 15:35:53 UTC 

Hi there 

I have the garden zones like the diagram. And I want zone 4 a 3 run the same amount of time. Currently they use different whisperers and have different schedules what makes the grass to present in summer dry patches. I would like to force to run 3 and 4 the same amount of time.

Should I use only one whisperer attached to both zones (3 and 4)? 

浏览: 950   回复: 3

Increase Run Time Per Zone

Don Carli
更新时间 2024-07-04 18:58:45 UTC 
话题: Netro App

Hello,


I have a number of zones that I would like to run for 180 minutes. Can you enable this for me?


Don

浏览: 873   回复: 2

Metro timer

Anne McNamara
更新时间 2024-07-04 13:16:31 UTC 
Everything shows it should be running, but it doesn’t wake up. I have it set for online during watering periods. It says it’s communicating but it’s not running. How do I wake up metro when I want to communicate
浏览: 871   回复: 1

Red dot

Jean Paul Lasserre
更新时间 2024-07-03 18:53:21 UTC 
What is the significance of a red dot next to the green bell ? 

Do not see anything anywhere and have not received any notice.

Thanks

浏览: 871   回复: 1

Export a summary of zone settings?

Steve M
更新时间 2024-06-30 23:53:31 UTC 
话题: Netro App

Is there a way to view all the input settings for a given zone, to wit, soil types, slopes, species, etc? It is difficult to check the data going screen by screen. Perhaps an Export or Summary capability I have not yet discovered?

浏览: 848   回复: 1

Adjusting for tree cover

Steve M
更新时间 2024-06-30 23:47:30 UTC 
话题: Netro App
Much of my non-lawn landscape area is sheltered by heavy tree canopy, meaning light rain does not reach the ground in the same amount that weather apps might report. If I find that smart zones are not getting enough water, how would I tweak the zone settings?
浏览: 837   回复: 1

all connections good but sprite wont open any valves.

Douglas Ely
更新时间 2024-06-29 11:36:11 UTC 
One day, the Sprite just stopped opening the zone valves. We tested and reconnected all the wires and deleted and re-installed the Sprite. Still no luck. Ground is good too. What could be wrong?
浏览: 882   回复: 1

app crashing

Christoforos
更新时间 2024-06-28 14:13:56 UTC 
话题: Netro App
Hi I install the app on my android tablet but when I am trying to manually water my plant on SPRITE-12, the app is always crashing. I try everything with no success.


Can you please help.

Thanks

Christoforos


浏览: 918   回复: 1

Netro sprite-6 with power adapter 600 ma?

Nuno Fs
更新时间 2024-06-28 12:33:25 UTC 

Hello 


Just bought a Netro sprite-6 and a power adapter 600 ma but the sprinklers go up but not down, why? Could it be the amperage?


I exchange the power adapter for a 800 mA and i still have the same problem. 


If i do a manual irrigation and turn  it off in the middle it doesnt turn off,but if i tried once more to turn it on it turns it off....

Nuno

浏览: 863   回复: 1

programs overlaping (smart scheduler and watering adjustment)

Alfonso Olias Sanz
更新时间 2024-06-25 10:19:26 UTC 

The smart schedule overlaps with the watering adjustment program that runs when the moisture goes below a %.

Yo can see here that zone 5 run 10 minutes the program and then 37 minutes the scheduler.  It has no sense and it is a waste of water.


  1. After the watering adjustment run, the smart scheduler should recalibrate the timing based on the humidity of the land.
  2. I have the whisperers, the whisperer should monitor the humidity and stop the smart watering once it reaches 99% of humidity but it seems the program runs all the way.

This could be improved in the application.

Thanks for your support and keep up the good job


浏览: 897   回复: 1

Netro Spark

Juan Manuel Fernández de Sosa
更新时间 2024-06-22 20:41:47 UTC 

En relación con mi pregunta anterior ya he visto que poniendo el riego nocturno a las 23:30 se acepta, pero si se pone a las 23:59 sale el error. Por lo tanto anulen mi anterior pregunta, aunque me resulta algo extraño que no permita 23:59 siendo el mismo día.

Saludos.

浏览: 880   回复: 1

Netro Spark

Juan Manuel Fernández de Sosa
更新时间 2024-06-22 20:24:29 UTC 

He instalado mi nuevo Netro Spark. En modo smart produce demasiados riegos en una determinada zona de forma muy constante, y con demasiado tiempo. No me parece nada lógico. Quiero dejar eliminado el modo smart y programar personalmente el riego. Consigo programar un riego de las cuatro zonas que utilizo en un determinado horario de la mañana, pero cuando voy a añadir un segundo riego diario por la noche me da un mensaje "ERROR: Program cannot cross a day".

¿Significa esto que solo puedo programar un riego al día? Muy extraño, mi anterior programador permitía tantos riegos diarios como quisiera simplemente indicando las horas.

Por favor, una solución, porque si solo se puede programar un riego al día no me soluciona nada este dispositivo.

Gracias.

浏览: 892   回复: 1

Start two Zones at the same time

Timmmee
更新时间 2024-06-22 18:15:57 UTC 

Dear netro team,

I missing the function that I can open two zones at the same time.  If this is possible you could combine different valves.

This would be a huge advantage.


Thanks for your response. 

浏览: 863   回复: 1

Netro Sprite offline

David Domingues
更新时间 2024-06-20 06:58:04 UTC 

Hello,

Since 2 days now, my netro Sprite is offline.

The light is solid  but quickly blinks each 6 seconds.

What should I do?

Are Netro servers online?

Thank you,

David.

浏览: 861   回复: 1

Where is the documentation on how to use the app?

Lance Blaise
更新时间 2024-06-20 03:41:17 UTC 
话题: Netro App
Where is the documentation on how to use the app? I have no clue how to set my own schedule or how to use the smart scheduling... I can't find anything on how to use this app at all and it's pretty confusing. I am looking at the app and it seems to have smart watering enabled, but there are times where it's skipping 3 days randomly and there is no rain that is supposed to take place on those days, so no clue why it's skipping those days. Can someone direct me to where the documentation is for using the app?  Thank you. 
浏览: 874   回复: 1

network error

paolo cellini
更新时间 2024-06-18 10:24:07 UTC 
话题: Netro App

Hi

i have a Netro app

on ios with a 12 station 

Starting this morning i receive a 

Network error message


i restarted/ re connect

same message


May i need a new firmware ? 

浏览: 1082   回复: 3

Weatherflow Tempest PWS Weather Provider

cseward
更新时间 2024-06-17 19:59:17 UTC 

I noticed that Weather Flow PWS was added as a weather provider for Netro and successfully linked my Weather Flow Tempest with my Netro Pixie Z1+Hub+Whisperers.  However I have a few questions:


1) There seems to be no way to remove or change the link to Weatherflow, like selecting another station.  Can you add a way to do that?  


2) Since linking to Netro, I have changed the name of my Tempest Device on their platform from the default serial number to a descriptive name, but Netro still shows the old name for the device when I click on it in the Weather Provider menu, is that a problem, or are they still linked?  (and if it is a problem, how can I update the link?)


3) What data is actually pulled from Weatherflow?  The forecast shown in the Netro app does not line up exactly with what my tempest shows, nor do the rainfall totals on the discover tab.  


4) I have also linked my Tempest with Weather Underground and can use them as a Weather Provider instead.  The Netro app says Weatheflow PWS shares 9 days of forecast and 1 day of history, while Wunderground PWS shares 7 days of forecast and 7 days of history.  I prefer not relying on an additional middleman to link my tempest to Netro, but is it better to have the additional history or additional forecast?

浏览: 899   回复: 1