Salve, quanto deve risultare l’umidità del terreno in giardino? Il sensore mi indica sempre tra i 96 e 97%. 

Please

I have had smart cotroller netro for 3 years. Never problems! 

Now i d like to buy z1 pixie with hub! But is it essential the hub for smart controlling? And if yes the hub has to be connected by lan to the router? 

Hello, I have 5 sprite-type irrigation controller units installed. In one of them, the irrigation stops after approximately 14 seconds on all channels, although it still appears as watering in the status. We have measured the electrical resistance and it is normal.

Why do my zones only activate for 2 seconds?

I have one sensor that is controlling 5 zones, in the last few months it has rained for several days and the humidity recorded has always been 100%. For three weeks however it has not rained anymore and the soil has started to dry out and so has the garden, because the sensor continues to report 100% humidity skipping the irrigation cycle. How can I unlock the sensor humidity reading?

Could you add a pause feature in Manual run? When I am running a zone, sometimes I need to halt the run and make an adjustment or fix a leak and then turn it back on. Right now, I have to stop the manual run and then start all over. 

Hello, I have activated Continuous Monitoring on my Wispering gen2 which means I should get an emediate update when the moister has changed.

But I don't get any update/ change until the aut hourly upate of the measurement is done.

My app on my phone say that the zone is on watering but when i look outside nothing is happening !!!

Help! How do I set up my controller to a connect to my new router?

Vincent Devlahovich 

805-813-1216

Loyal customer

Hello,

I had to change my google password and now I lost all my datas from my last installation in my Netro system.

What can I do to find it again. Must I install everything new?

Who can help me?

Thank's

Konrad

Hi,

I have 4 zones and a master valve. When I run any of the zones, they won't shut off when the timer runs out. If I switch the AC power off, then the valve will shut. I have checked the valve and it has no issue with opening and closing except when the sprite is running it. I tested cables for continuity, and I have tried swapping cables with no change. My ac power pack is AC 24v.

This issue affects each of the valves but only when controlled via the sprite. The valves are fully operational otherwise.

Hoping for a fix, otherwise will return to Amazon under warranty and get another brand.

I changed the sprinkler head on zone 5 after installing the new controller. All zones work but 5. I can run it manually. It won’t work on smart watering.

Why is connection lost with my cover on. But when I take it off it then reconnects? My lawn once again looks like crap because this thing glitches out.

My Netro controller is about three years old. I recently changed my Wi-Fi router about two months ago.  I repaired the controller with the new Wi-Fi, all seemed to work for a few days. Then the controller started cycling on and off of Wi-Fi. There are windows of several minutes that I can communicate with the controller, then windows of several hours when I cannot.  The light on the controller is solid for about 20 seconds, then three slow blinks, solid for 20 seconds, then three slow blanks, this pattern continues indefinitely. I have repaired the controller to WiFi several times. I have unplugged and then plugged the controller back in multiple times. Nothing seems to resolve the issue. It’s frustrating when I’m changing sprinkler heads and have to wait several hours to try a manual run to test the new heads. Has anyone else experience this and more importantly solved this issue? Thanks for the help!

Seems like my system has a mind of its own.  It'll water on time for a few weeks then stop then water again. 

I cannot get the system to set up our county water restriction schedule. It is Wed and Saturday up to 10am in morning and after 6 pm at night. I would really like to run each zone once in the morning and once at night!  Any suggestions before I get fined $200.00?

Am I able to create a schedule for new seed that allows me to add 2 watering times (1 in the AM and 1 in the PM)? Right now I had the create 2 separate schedules. 

I have a Flume on my master water meter.

Is anyone familiar with any integration between Sprite/Spark and Flume?

Thinking of scenarios like:

If Flume water is already in use heavily (can be defined) then delay watering

Logic between Flume and either Metro to help with faulty valve / leak detection based on water (augmenting Spark's*)

If Flume detects water is shut off, don't run any Netro programs

* I read in Wency's reply at (https://netrohome.com/en/forum/posts/3479/show_question) that 

"The faulty valve detection relies on monitoring the voltage and current of the water valve's operational state. As for measuring the volume of water consumed, it's a consideration for future developments."

.

I have a Sprite which has 5 working zones which are all connected to smart watering, 4 to sections of the lawn and 1 for the garden.  The lawn zones all water automatically but the garden zone only waters manually.  All zones have been set to water automatically via smart watering.

What could be the possible cause of this please.

I have 6 zones and all but zone 1 run.  I start running manually and app says watering but nothing.  I checked the wires, none loose.  It will run randomly but I’m getting really frustrated.