Hi everyone,

I'm experiencing a serious issue with my Netro Sprite 6 controller. It connects correctly to Wi-Fi and appears online in the app, but when I try to start irrigation manually, the app just stays on "in communication" and nothing happens.

Here’s what I’ve already tried:

- Restarting both the app and the device  
- Using a different Wi-Fi network, including a mobile hotspot  

Despite these attempts, the problem persists.

Thenks

Why is Whisperer not showing any moisture reading at all? after working fine for days, it just stops sending moisture info

Hello, I’ve installed netro app on my iPhone, followed the procedure to connect the spark 16 and everything is fine, but when I try to activate valves with the app, the led turn white.

If I remove spark 16 from the app, the led turn green and I can only activate valves from the controller,

Any solution?

Thanks

Davide

Hi everyone,

I'm experiencing a serious issue with my Netro Spark 8 controller. It connects correctly to Wi-Fi and appears online in the app, but when I try to start irrigation manually, the app just stays on "in communication" and nothing happens.

Here’s what I’ve already tried:

- Restarting both the app and the device  
- Using a different Wi-Fi network, including a mobile hotspot  

Despite these attempts, the problem persists. I also tested the solenoids with a multimeter, and they’re working correctly. If I activate the valves directly from the controller, they respond as expected—so it’s clearly not a hardware issue.

I should also mention that I previously had the same problem with two Sprite6 controllers. That’s why I switched to the Spark 8, hoping it would solve the issue. Unfortunately, it hasn’t.

To make matters worse, scheduled programs aren’t working either.

This is an urgent situation because my plants are currently without water. I’d really appreciate any help or suggestions to resolve this.

Thanks in advance,  
Stefano

I have some scheduled zones using programs and I'm seeing that the zones later in the program are being cancelled and not completing the scheduled program. What is causing the schedule to be overridden? It's a problem because those zones that are being skipped are not being watered at all. 

Hello,

I have a strange situation:

- App reports controller as off-line, sometimes it reports on-line for brief periods. It was working fine till three days ago

- Controller has green light

- Web app on the netro site reports on-line and works

- The controller is watering

- The Wifi near the controller is working and I have not changed the password or settings

- I have tried forcing it to change the wifi, I get the bluetooth light and the controller is detected on the app via bluetooth, however it fails after I insert the password for the wifi. This is odd since the device is connected.

I suspect there is a synch issue between the App and your servers. Help would be appreciated.

I have two Whisperers that I move around to various parts of my graden to get comparative readings of sunlight and soil moisture.  I really do not know how to interpret the moisture readings which generally range from 50% to 98% but can be as low as 30%.  Soil type varies from a clayey loam to heavy clay.   How do I know when watering is required?  Does the meter measure the capillary water?  The adhered water?  The percentage of voids filled with water?  How does Netro calculate the percentage of water and what do the readings mean?

I added the Netro whisperer 2 soil sensor to my ficus pot. The sensor gives me contradictory messages. It says that next watering should be in one week but every night it sends a notification to 'water the ficus sensor's. What should I do? 

Hi everyone,

I’ve been using a Netro Spark (8-zone model) for some time, but recently it stopped working properly.

The controller connects to Wi-Fi and appears online in the app, but when I try to start any valve (manually or via schedule), it says “communicating” and nothing happens.

Here’s what I’ve already tried:

• Restarted the Spark multiple times
• Performed a full reset (12 seconds on RST button)
• Re-added the device in the app
• Tried to trigger irrigation manually from both the app and the controller
• Confirmed that the system works when I open the valves manually from the controller
• Tried different power supplies
• Connected to a mobile hotspot instead of my home Wi-Fi (same result)
• Updated the firmware to the latest version (v3.3.0)
• Purchased a brand new Spark controller and tested it — same exact issue

At this point, it looks like the issue is not hardware or network-related.

Could it be a firmware bug or a server-side problem?

Any help would be greatly appreciated!

Thanks in advance,

Stefano Mauri

Hello,

Since a few days my Netro is not receiving data from the different Whisperers connected and all of them are well connected to Wi Fi and charged. I am not able to run manual watering, only the planned ones go. It looks like there is an issue or with my Netro Spark or with the Netro Server. I am based in Italy. Please let me know. Thank you.

My whisper smart sensor is contacted to my garden plants zone at my holiday home. The smart schedule is not working.this is due to the fact that the sensor battery says it needs charging. Obviously I can’t charge it as I am not there. But I can’t seem to find a way of disconnecting the sensor from the program and on to smart schedule 

Can you change the order of zones in a current program without having to create a new program?

Hi everyone,

my Netro Spark 8 controller connects correctly to Wi-Fi and shows as online in the app. However, when I try to start irrigation manually from the app, it just stays on “in communication” and nothing happens.

I’ve already tried:

• Using a different Wi-Fi network (even a mobile hotspot)
• Replacing the controller with a new Spark 8
• Restarting both the app and the device

If I activate the valves directly from the controller, they work fine — so it’s not a hardware issue.

Any suggestions on how to solve this?

Thanks in advance!

– Stefano

My whisperer used outdoor gave me an alert here thru the Netro app saying it has 19% battery remaining. What does it mean? Is the solar no longer working? Is there another way to recharge it or can the rechargeable battery be replaced?

Thank you

When pausing a zone for any reason during watering cycle, the zone is skipped. Is there any way to pause it then resume the watering cycle in the zone that was paused?

When I Launch the program , it stop after few minutes…

I don’t know why ?

I cannot activate my PIXIE-Z1 to water, it is with brand new batteries, it says 100%, it is online and app and webpage react as all is fine and watering, but unfortunately nothing happens with the device. It works if I push twice the button on the device.

What could the issue be?

Thank you in advance

How do I reset the length of time sprinklers are on?

Hi Friends, on The APP I Turn on a sector manually but when I ask APP to Turn Off, dont do!

ONLY Turn off if I unplug The system .

Can you help?

It seems like, from my communications with the support team, that the soil moisture indicated by Netro does not factor into sprinkling times other than understanding how sprinkling time changes soil moisture (essentially guesses soil type). I have had to very expensive weather stations, and both failed to accurately report rainfall in as little as three months. With religious cleaning of them (ladder climbing-dangerous) neither accurately reported rainfall for more than six months. My first station Accurite 5-1) was replaced at three months and I gave up and bought an Ambient Weather WS2902-C, which lasted less than a year. So….

Why not have the Whisperers determine actual rainfall- or better yet- make your next product the only digital rain gauge on the planet that actually works? Or, perhaps gen 3 of the Whisperer can have a rain gauge built in. When you get multiple Whisperers  per zone, working in the software, the soil moisture readings alone could make reported rainfall irrelevant. 

Thanks,

Kirk

P.S. The support team HAS to stop using the term “soil humidity”. It makes them seem like they don’t know the difference between a fluid (water= moisture) and a gas (vapor=humidity). The Whisperer cannot calculate evaporative likelihood and doesn’t know the air pressure above the soil, so it can only measure moisture, which would, to some extent, measure the influence of water vapor on the moisture, depending on how it was being measured.