I can't connect both of my two Pixie devices to Alexa — I can only control one.
How can I fix this issue?

Thank you.

I have a digital water metering in my house from my water supplier. So know the exact amount of water that ist running for all zones If netro ist running and watering the Garden. Unfortenately i can Not find an Option, to Tell netro how much water in qm per hour is running for wach zone. IT would be great If that could be implementated to have an exact number of qm water that ist uswd for watering each zone. So gar I know netro gives only an wstamated number of water used for wach zone, depwnding in size of watering area and Type of watering equipment.

Anyone else have problems with whisperer/whisperer 2? The ones I have just seem to stop working out the blue.  The current problem unit is a whisperer 2 which was sent to replace a broken whisperer.  It comes on, lights up, and shows 100% charged when plugged into a usb power source.  As soon as I unhook the power source it stops working, and oower button does nothing.

How do I change and save schedule? 

I have installed a new Sprite - however, I have 3 common wires but only two slots - and only one wire fits in each slot...

Hi

Suggestion:

It would be great if it was possible to have a better overview in the Netro app when using multiple controllers. 

For instance, we have 2x Spike 6 zone controllers and 1x Pixie in our setup and it's currently tricky to have a overview over all zones scheduled in these controllers without switching back and forth between them. If only Schedule tab would list all our zones setup in all our controllers :-)

Dear Fellows,

I will be away for over a month and want to confirm the best practices to ensure my Netro Stream batter operates reliably throughout this period. Could you provide tailored recommendations based on my device’s current configuration and usage?

Device Details:

• Hardware : Netro Stream 1.0
• Firmware: 1.0.0

Please advise on any critical steps I might have overlooked. I aim to finalize my plans.

Thank you for your assistance!

Best regards,
Kelvin

Can I send my controller in to get it repaired? 

Hi there I use the netro smart feature and the whisperer. 

The smart schedule for zone 5 watered 28 minutes at 5am and the sensor measured 99% humidity.  Then it watered again at 6am... which is obviously a waste of water as the zone is already 100% humid. So it look like when the program starts it does not take into account the humidity again until the next run for that zone. 

For zone 5 I am using regular mode. Not the Deep or EPA. 

I also have the condition that 

- Sensor to report every hour

- skip watering if above 60%

- Sensor firmware 2.0.1

Sprite-12

I want to utilize automated rain delay feature.

If I have my 11 zones enabled for Smart Zone watering, the zones will water in a random order.

I need them to remaian in order 1-11. I cannot yet find a readon why.

Not much fun sitting on my lawn when a zone unexpectedly turns on.

If I use a manual program, then the rain delay feature cannot be used.

Is there a way to enable an automated rain delay in a manual program?

and/or

run the zones in an order when utilizing the Smart Zones?

And yes, most of my zones have the same environment settings

Dear Netro Support Team,

I hope this message finds you well.

I am writing to inquire about purchasing a replacement battery for my Netro device, which has recently stopped working due to battery failure. Could you please provide information on how I can order a replacement, including the price, availability, and shipping options?

The model I am using is PIXE, and I would appreciate any assistance or recommendations you can provide.

Thank you for your support, and I look forward to your response.

Best regards,

Minh Thu, Nguyen

I’m sure my transformer is not working.

I have Netro 6

Please help

I have 3 Whisper gen 2 sensors 2 have firmware 3.1.1 and one has firmware 3.1.5. How do I update the firmware on these devices?

I  bought a new Pixie and I connects with my router, it does not connect to the internet. The suggestions in the directions do not solve the problem. Any suggestions?

Cómo puedo hacer que el programador riegue más de 60 minutos. Solo me permite 60 minutos por programa

Gracias Marcelo 

One of our sectors runs inside a greenhouse now. Apart from soil type and sprinkler head type, does anyone have advice how to optimise sector settings for this situation? I feel the influence of sun and normal outdoor temperature is different, and rain is completely absent in this sector. 

May I suggest to add some sector setting that it is inside a greenhouse?

Thanks

Perry

Some translations in the app for the Dutch language are a bit off. The wrong translation from English to Dutch is used.

For instance to save a setting in Dutch the word “sparen” is used. “sparen” in Dutch is used for instance to save money. The proper Dutch word to save a setting is “opslaan”

Another one is how “disabled” is translated. It currently says “gehandicapt” which is the Dutch word for disabled people. When a setting is disabled the proper Dutch word is “uitgeschakeld”, literally meaning off-switched

Kind regards,

Perry

Hello, please take in consideration to extend the possibility to link the whisperer up to 4 zones at least. I have 4 zones enabled on my netro sprite and the smart zones enabled and linked with the whisperer only on 3 of them. How can I setup all the 4 zones to follow the same smart program? Now the 4th zone (not linked with the whisperer) can follow only a manual program or a smart zone which is different from the other 3. I would like to water the garden with all the zone at the same time.

Have a whisperer working fine.

As the battery of my second one could not be charged (even by cable) bought a new one.

The new whisperer is blinking white, the phone, the router and the new whisperer are within 3ft of each other.

Nothing happens on the appli, see only the existing whisperer not the new one.

What should I do ?

¿Es posible en un Programa manual que se repita en más de un horario al día?. Sólo he podido indicar en cada programa una hora de inicio y una hora de fin, me gustaría en ese programa que se lanzase una vez por la mañana y otra vez al final de la tarde