I’ve got mine watering during a rainstorm a couple times or when the weather is predicting rainfall. Any way to adjust whatever number it’s using to decide not to water?

Hi,

I’m not sure that I can trust this Spark Controller anymore.  Woke up to notifications of zones being watered when controller is programmed to water on MWF.  Moisture levels in all zones was okay on all zones and smart level is only set to basic.  According to the notifications the controller was watering on 9/8/21 instead of 9/7/21.  It’s like the calendar on Netro’s server is set to the wrong date.  Very disappointing, and I don’t know if I can trust the controller going forward. the controlle

Hello,

I bought 2 whisperers and 1 controller.

I set up 1 whisperer as a sensor before trying out the controller because it arrived first.

Then when I got the controller a few days later I "deleted" the sensor and factory-reseted it so I could add it to my controller.

Now I have an empty "Plant Sensor" section in the app (and in the webapp) and I can't delete it

How do I remove the empty section?

I have programmed the 8 zones in my Sprite water controller to run 20 minutes at each station. However, it keeps watering based on some manual settings as noted in the red circles below that I have changed over and over to coincide with the program. It still just resets to 1 minute on several stations. What do I need to do to fix this?

Where are the moisture sensors on the whisperer?  On one of mine, the ground stake broke and I was thinking of replacing it with a stardard metal stake. Will this work or is the moisture sensor built into the ground stake? Thanks! 

If I leave my sensor for a while it stops recording new data. The days where there is no data is recorded as a zero. This is obviously not correct.  Any plans on updating this?

Hi

Despite numerous trials i cannot connect the box to the website. 

Help needed

Regards 

We had a huge lightning bolt crack by our house and now my new Netro watering system is offline. Is there any way I can get a new power supply to try and get the system back online. I am really bummed that it’s offline. 

We recently had chipmunks chew through  the fiberoptic connection for our computer hookup, not before we were advised to install a new Bell router with a different ID and password. But I can't seem to get the Netro system to recognize this new router and its ID, and it has gone offline. Several attempts to get it to go online failed.

The control panel has a slowly flashing white light indicating that it is in a holding mode, I understand.

Can you help me through a re-connection please? The system has been a life-saver to date....

Neil Hobbs, Sydenham, Ontario.

It rained yesterday yet my moisture sensors have not changed. How do you reset it or get it to measure correctly??

i have a new xfinity box. all i get is fast blinking light . i try to reset does no good. i have a netgear router too. im at wits end !!!!!

I want to turn watering off without deleting schedules.  I need to do some repairs

Buenos días.

No encuentro los manuales en Español.

Pueden indicarme donde los encuentro en la web?

Gracias 

Each Smart Zone can be set to a preset, e.g. Frequent, Deep, Boost, EPA, etc.  If you click Customized, you can choose the Min and Max Soil Moisture, and the Flow Rate (inches/hour).  Presumably, there is a default value of these three choices for each of the presets.

How can I find out what the presets are for these three values?  e.g. for the EPA preset, what is the Min, Max, and Flow Rate?  Same question for all of the Smart Zone presets.

Thanks!

Ken

It has rained for past 2 days and it still says moisture in grass is 50-60%. I don’t have sensors but my understanding is it supposed to change due to weather forecast! It doesn’t so not very smart!

What do the attention icon means it appears sometimes next to the smart schedule 

Hi

My watering unit is programmed to water my lawn as necessary under the programs algorithm. However, I have numerous days when the watering is done twice— for exam0e it will run all the zones and immediately run the same zones again.  Anyone know how to fix that?

Hello. I cannot chance The nome of zone. Only Zone1- Zone 2 but IS more nice with name. Can you help me ?

I installed my Whisperer and it seemed to work but after a couple of days when I checked the APP it just shows 0 at all three datafields. I see values in the overview (weeks, month etc.) though. What can I do to correct this? 

How do I give access to the guys that blow my lines out when I'm not there. Is there a way for them to open each zone without me giving them access to my wifi?