Hi all,

I use 1 Netro Spark with 2 Whisperer sensors.

All devices are added to the app and i can see in the app.

In the app I can open by dropdown on top the Spark OR the Sensors. When i open there the Spark and go to setup, then i can can see the entry sensor, but the i can not add the sensors i have. 

I want to connect the sensors to the spark and the spark should Start the watering in relation to the real condition measured from the sensors. 

But how to connect the Whisperer to the Zones? 

Thanks for support!

Netro Support Team,

Where do I find the calendar view?    Is it the schedule icon on the bottom of the home screen?

I simply want to view when my sprinklers will run in the future when using "smart watering", "level: advanced".

I find that trying to find answers to questions when I am limited to community postings is cumbersome.   A good detailed manual would be very beneficial.

John Kollehner

Houston, Texas

My Netro control does not conect to internet. I think is broken. Do you know if there is any technical support in Spain to repair it?

Thank you

Hi there

also calling from Spain. Since today my Netro device is not connecting to the cloud. Re-assigning to WIFI via the APP is not working.

In my network + configurations nothing has changed.

Can you check maybe log file on your side?

Serial No of the device is cc50e34a7616

Strangely my Netro hubs are working.

UPDATE: reconnecting with an Android app + device worked like a charme. BUT if I start watering manually the watering is not starting, status is showing "communicating" for ages also after restarting devices many times.

Hello, 

Problem: Ventiles open by Netro successfully (by schedule or manually. But after the run time the Ventiles do not close. The only option i have is the switch off the Netro. Than the ventiles close. 

Ventilttest successfully done (see screenshot)

Whats wrong? 

Hello Netro Support, 

The Spark startet watering today at 4 am as it was calculated by whisperer and weather. 3 Zones got water, but instead of watering 10 minutes the gras got 3 hours water. 

I wasted a lot of water, this is far away of smart watering. My old installation from Gardena / Husquarna never had such problem. 

The spark was not able to close the Ventils! 

The only way was the make the spark powerless. 

What’s wrong? 

Again: the test procedure of the ventiles works without any problem, spark open AND CLOSE every ventile step by step! 

I am using 1/4 inch soaker hose for my netro controlled irrigation system, yet that is not an option in the "sprinkler type" selection box. What Sprinkler Type should I choose as an equivalent? Are there any plans to add Soaker Hose as an option in a future update?

I have small lengths of soaker hose encircling the base of each of my 20 bushes with lengths of standard hose running between them. for a total lengh of 50 feet of soaker hose.

Hello! For a few days the watering has stopped in the middle of the program, although in the app it tells me that it is watering. Sometimes I try to irrigate manually and the irrigation does not connect either, but in the app it tells me that it is watering.

Hello everyone,

Is it possible to set up more than 3 users in the user administration or are there plans to increase this number?

Best regards
WH

Hello 

Actually i have 3 sensors in my garden and 2 are properly seitched on instead one randomically switched off and i see it because there is no data in statistics

How csn i solve it? 

Czn i check snything?

Thanks

I purchased the smart valve (PIXIE-1)  and the sensor (WHISPERER-2) for my vegetable garden, but unfortunately the pixie-1 releases a few drops of water when it is in irrigation mode, my watering system is ecological, I collect rainwater, 

because the pixie-1 does not it passes water with little pressure, the pressure is low but sufficient for irrigation.

This wasn't written anywhere.

Is it possible to configure the valve to use it with low pressure?
thank you all

Leandro