I've installed 2 Spark 16s to control a 26 valve system.  All the valves are working fine with this setup.  Are there instructions for the best way to configure this?  I have low water pressure and can't run 2 valves at the same time, so some synchronization between the 2 Sparks is needed.  I could manually setup restrictions on each unit, so they can't overlap, but that seems too coarse.  Any ideas about the best way to program this?

I really hope that you change the manual run portion of the Netro App back to the way it was. As a dealer, installer, and owner, I find the changes made earlier this year make for a very time-consuming, difficult, and glitchy experience. To schedule a runtime of more than 1 minute is a pain and usually the timer is unresponsive.

Hello everyone from Spain.
 I have received my new whisperer but I can't get it to give me the temperature and humidity data correctly.

I am concerned about the excess water that I may waste.

Can somebody help me?

I attach a photo.

Thank you very much.

To my controller shuts the valve off automatically after a little over a minute every time I turn it on to manual run whether I set for 10 15 20 minutes it doesn't matter this is very frustrating

Hi, Would it be possible to use Netatmo network as weather provider? Each member on this network has its own weather station and you can connect to see the real time weather on each station. As an example, my brother has one which measures temperature, humidity, wind speed and direction, rainfall,... It would be nice to use real time data instead of expected data.

Regards

Rafa

https://weathermap.netatmo.com/

I have a 2.5 acre site half of which is controlled by an Orbit timer and now the other half (the field) is controlled with the new S-12 .

The water is pumped out of a seasonal pond and the pump is turned on whenever the zone(s) are turned on through a standard switch from the timers to the pump.

The problem is that I get a pump fault on the Orbit timer if the pump wire is left hooked up to the Netro timer. They are wired such that both 

timer"s pump connection is to a common wire to the switch. This was not a problem when I had two Orbit timers. What can be done? - run a separate wire to the switch? Do something in the software? Need to know soonest.

Thanks,

Vance

May I use the whisperer to check grass?

I tried out the new web portal to manage my 3 pixies and their connected whisperers. I modified 2 of the 3 (if you're looking at my account, they're named "Potted Plants" and "Front Lawn") to use my Weather Flow PWS that I have in my backyard, since I have one and I noticed that this option does not exist in the iPhone app. Upon doing so, the iPhone app crashes every single time. I went back to the web portal and changed the weather provider back to the default "Netro Weather" and the iPhone app no longer crashes. If I changed it back to the Weather Flow PWS, it'll crash.

I presume it's crashing because the site offers this new choice for weather providers but this same choice hasn't yet been pushed out to your iPhone app yet and the app doesn't know what to do. I guess until the iPhone app gets updated I'll use the default provider, but this is a pretty annoying bug since I constantly get better results with my weather flow pws than any of the iPhone available options.

on my iPhone it is nearly impossible to read a lot of the characters because they aren’t in dark black letters it’s a very light thin font. It seems like it would be a lot easier to read if the application supported dark mode. The other option would be to set a preference to increase the font size. That seems like pretty standard request so I’m hoping you guys might be able to get it in a future build.

Is it not possible to have the watering irrigation of more than 1 year?, today is July 2 and I cannot compare the monthly irrigation of June 2022 with the June 2021… I think a minim of two years data its a must.

Jose 

I’m running drip irrigation and need long runs, way longer than 60 minutes. Why is the max manual run and 1 time run on the schedule only 60 minutes?

I'm no longer able to use the Netro app. I'm getting an "Error: Can't find user" message.  I'm using the correct user to login on this forum, so my credentials work, just no longer with the app. How can I fix this please?

Pat.

Hi! The spp can register water flow meter with Pixie?

Hi I just got another Controller can Iuse one app to manage both controlers?

Thanks,

Zev 

Hello

I recently got a handyman to install the 6 Zone Netro system. My home lawn has 6 zones.

When the watering schedule is on, the issue I have is that the sprinklers connected to Zone 6 always come on when any of the other zones are working.

So, if I have 2 minutes set for each zone : When Zone 1 sprinklers are on, Zone 6 sprinklers are also on. After that When Zone 2 sprinklers are on, Zone 6 sprinklets are also on.

Is this due to faulty wiring connections are something else in the software?

thank you

Is there a way to not have manual runs conflict with the smart schedule?  At times I turn sprinklers on for kids to have fun or to test a newly installed head for a few minutes. These manual runs (even for a minute or two) in these zones are not being run during the next scheduled run. This is frustrating and now I need to do a lot of manual runs to ensure lawn gets appropriate amount of water and is basically taking away my ability to auto schedule. 

Thoughts?

What are the smart watering settings for each variable that result in the least water used? For example, I assume fully shaded for amount of sunlight would result in the least water used for that variable.

I have 2 zones that stopped working. 

1 I know the issue and not able to fix. The other stopped after working all year. Communications says it's fine and water is going to control valve. But why all of the sudden when nothing changed