Hi I have had to send back my spark due to a problem with one zone not operating, I’m now trying to do a reset on my whisper, I have pressed the power button quickly 6 times, on numerous occasions and cannot get it to reset, any help would be much appreciated. New Spark arrived and working well, l just can’t seem to reset the Whisper no matter how many times I try the on/off 3 times. Are there any other action I could do or do I return it for a replacement?

I have an existing 18 zones irrigation controller which I am replacing. I require 2 controllers. No master valve or pump.

It is possible to connect both commons to the existing common connected to the 18 zones?

Thanks 

Is it possible to connect the Netro Pixie Z1 to the wifi and to the App using the Netro Sprite without the need for the Netro Hub?

Thank you

Someone can help me to connect to my unifi Wifi tm sensor Pixie ?

All goes OK unitl last step.... when it tell me that I connect connect to it

thanks

Hi

I am struggling to set up the watering days

There isn’t an option for 4 / 3 / 4 rostered days which is are allocation here in Perth Australia

Please advise

TIA 👍

My unit has been working great . However, the relay no longer trips when a zone is activated. Am I supposed to have 24v A/C between M and C (on the right side of the panel, not the zone side) when a zone is active? I can trip the relay if I pull it from the Netro. Some sort of voltage output map would be helpful. 

I bought a Netro Spark to replace an existing controller (a Raspberry pi based Open Sprinkler system) which exploded probably due to a shorted solenoid.

I read that the Spark can detect solenoids that are drawing too much current; is it safe to connect the Spark to shorted solenoids without worrying about damage to the controller?

Should I test all the solenoids with an amp meter first just to make sure?

Hi - I am trying to determine if the 12 station Netro  spark would be easy for me to install.

I currently have a rather old rain bird system with 16 valves.

I think I understand the mapping of the com and individual values. But I am confused about the 24 vlt and my current rain sensor.

It seems like my 24vlt wires come from a pack/converter that is plugged into an outlet. Is this directly convertible - not sure how I take the orange wires and the devices they are connected to on the left of the picture to the new controller?

As well, would my current hunter rain sensor still work with the new controller, or do I need a different one?

Thanks for your help and advice.

I had just installed 3 whisper and two of them are showing temperature o 3xxx °C, while the third one is correct.

Is this normal? Or will be auto updated?

?

Hello all,

I just bought a Netro controller with only 2 areas setup and I like it so far. 

I was wondering if the noise and heat from the power supply was a  normal thing to happen.

Thanks in advance.

I've installed 2 Spark 16s to control a 26 valve system.  All the valves are working fine with this setup.  Are there instructions for the best way to configure this?  I have low water pressure and can't run 2 valves at the same time, so some synchronization between the 2 Sparks is needed.  I could manually setup restrictions on each unit, so they can't overlap, but that seems too coarse.  Any ideas about the best way to program this?

I installed my Spark yesterday and zones 5 through 8 do not work. I metered the valve on zone 5 and it is fine. I also swapped zones 4 and 5 and the fault stayed on 5. I tried connecting the zone to 6 and 8 and still received the fault. Is the controller defective?

Hello.
Is it possible to move a Zone, in my case: "Prato e back giardino" from Terminal 2 to Terminal 3 in a efficient way?
Let's say, for instance:  Copy Zone "Prato e back giardino" or Move "Prato e back giardino" from Terminal2 to Terminal 3, without being obliged to cancel the previous and reprogram all in a new Zone?

I've a problem with Terminal 2: the wire broke inside and I am not able to remove it ....

Thanx a lot
Gian Piero

My pixie won’t find my Wi-Fi. I’ve rebooted my router but didn’t help. 

Hi,

Netro spark can be configured and used as timer if no wifi access point are available?

It is possible to use it by connecting directly mobile phone with spark without additional devices?

Thx

I am unable to have my new whisperer working. It doesn’t light on even after half a day under the sun.

May I reconfigure localization of my Netro Spark without reset the device? I have configured the device at home and now installed at my summer house many miles far away. Thanks.

I have 2 houses and I wanted if it is possible, with a single phone to control 2 Netro
Cordially

Hicimos la instalación tal como figura el manual pero ni las electroválvulas ni la bomba de agua enciende cuando programó el riego. La app dice q está regando pero no funciona el riego.