More filters

Whispered wrong temperature range?

David Gomez
Updated at 2022-07-29 17:51:27 UTC 

I had just installed 3 whisper and two of them are showing temperature o 3xxx °C, while the third one is correct.

Is this normal? Or will be auto updated?

?

View: 2004   Answer: 2

Power device heat

David Domingues
Updated at 2022-07-09 17:15:45 UTC 

Hello all,

I just bought a Netro controller with only 2 areas setup and I like it so far. 

I was wondering if the noise and heat from the power supply was a  normal thing to happen.

Thanks in advance.


View: 2083   Answer: 2

2 Spark 16s linked?

Jim Simmons
Updated at 2022-06-22 14:56:08 UTC 
I've installed 2 Spark 16s to control a 26 valve system.  All the valves are working fine with this setup.  Are there instructions for the best way to configure this?  I have low water pressure and can't run 2 valves at the same time, so some synchronization between the 2 Sparks is needed.  I could manually setup restrictions on each unit, so they can't overlap, but that seems too coarse.  Any ideas about the best way to program this?
View: 2228   Answer: 2

Spark zones do not work

justjeff1972
Updated at 2022-06-20 13:51:18 UTC 
I installed my Spark yesterday and zones 5 through 8 do not work. I metered the valve on zone 5 and it is fine. I also swapped zones 4 and 5 and the fault stayed on 5. I tried connecting the zone to 6 and 8 and still received the fault. Is the controller defective?
View: 2059   Answer: 2

Move a Zone between Terminals

Gian Piero Pepino
Updated at 2022-06-03 12:13:40 UTC 
Hello.
Is it possible to move a Zone, in my case: "Prato e back giardino" from Terminal 2 to Terminal 3 in a efficient way?
Let's say, for instance:  Copy Zone "Prato e back giardino" or Move "Prato e back giardino" from Terminal2 to Terminal 3, without being obliged to cancel the previous and reprogram all in a new Zone?

I've a problem with Terminal 2: the wire broke inside and I am not able to remove it ....

Thanx a lot
Gian Piero

View: 2646   Answer: 1

Zone

Bertin Grégory
Updated at 2022-05-31 15:50:10 UTC 
Bonjour
Serait-il possible d’activer 2 zones en même temps réfléchi
View: 2730   Answer: 2

Pixie automatic water

Shirley Johnson
Updated at 2022-05-18 18:20:36 UTC 
My pixie won’t find my Wi-Fi. I’ve rebooted my router but didn’t help. 
View: 1926   Answer: 1

pollomito
Updated at 2022-05-10 19:31:57 UTC 

Hi,

Netro spark can be configured and used as timer if no wifi access point are available?

It is possible to use it by connecting directly mobile phone with spark without additional devices?


Thx

View: 1969   Answer: 2

Netro Whisperer

Fabrice GOUFFRAN
Updated at 2022-04-28 12:29:53 UTC 
I am unable to have my new whisperer working. It doesn’t light on even after half a day under the sun.
View: 2016   Answer: 1

Localization

JM del Amo
Updated at 2022-04-12 10:19:03 UTC 
May I reconfigure localization of my Netro Spark without reset the device? I have configured the device at home and now installed at my summer house many miles far away. Thanks.
View: 1979   Answer: 1

I have 2 houses and I wanted if it is possible, with a single phone to control 2 Netro Cordially

GERMONT Alain
Updated at 2022-03-23 10:10:18 UTC 

I have 2 houses and I wanted if it is possible, with a single phone to control 2 Netro
Cordially

View: 2063   Answer: 1

Netro Sprite 6 no enciende la bomba

Vanina Lesko
Updated at 2022-02-20 12:24:48 UTC 
Hicimos la instalación tal como figura el manual pero ni las electroválvulas ni la bomba de agua enciende cuando programó el riego. La app dice q está regando pero no funciona el riego.
View: 2263   Answer: 2

Manual watering stops before end of schedule

Patrice Kestenberg
Updated at 2021-08-29 16:13:57 UTC 

Hi,

I’ve got a sprite 6 system with 3 zones configured and no master valve

The watering stops before the end of planned schedule. 

So I’ve deactivated all smart function to check, manual launch planned for 5 minutes. 

It starts and after 15seconds it stops watering. 


Any idea why?

View: 2437   Answer: 1

no wifi connection mqtt blocked

paolo cellini
Updated at 2021-07-30 18:16:05 UTC 

Hi 

i received Netro programmer

no connection

i have a fritbox 7560 

the server status message says

mqtt blocked port 1883 

View: 2359   Answer: 1

Installing New Netro-6

Debby Plenert
Updated at 2021-07-25 14:37:04 UTC 

I removed an older controller and replicated the wiring when installing the new Netro.  Everything appears to be correct?  However, when watering is activated, the valves will fill up and vibrate or what not with water rushing internally.  But the sprinkler heads don’t pop up and no water comes out.  Any help here would be greatly appreciated.  Thanks!

View: 2271   Answer: 1

New install problems

M A
Updated at 2021-07-14 23:07:34 UTC 
Installed - but now only 4 of 9 zones work, thoughts?
View: 2193   Answer: 1

Set up additional device

Mark Vandeberghe
Updated at 2021-06-29 15:42:49 UTC 
Can I use my app to set up another device that will be on a different WiFi? It is for my Mother’s lawn and I would like to get it set up using my phone
View: 2265   Answer: 1

Installation of my Device

JD Dakak
Updated at 2021-06-28 18:15:34 UTC 

I am having difficulty setting up my timer.  I have Netro connections, but I can not seem to make my phone connect to schedule a time for irrigation.  manual does not have good information on trouble shooting this issue...


I need help with that.

View: 2067   Answer: 2

Installation of sprite

Mark Killeen
Updated at 2021-06-12 21:53:35 UTC 

I have all connected and seems fine but when testing turning on each station I get a "pending" but no sction!

Each zone then said"loading"  for 5 minutes each then nothing. Please offer any help!

View: 2014   Answer: 2

Whisperer won't blink white during setup

Kevin Westling
Updated at 2021-06-12 03:01:46 UTC 
Prior to installing a whisperer to my system, I set it up outside in direct sunlight for 5 days. When I try to add it to my Sprite, the light only blinks red once. I've tried multiple times to press the power button 6 times and it's still just flashing red just once. What am I doing wrong?
View: 2197   Answer: 1