And we are off and running.   Whisper went in the ground and started reporting right away.  Would be nice to connect it to my Ambient weather station as well.   

I purchased a whisperer to automatically adjust the watering of problem areas. I received the product and turned it on. The white light began pulsing. I went to the Netro app and selected the account I wanted to add the whisperer to. When I go to "settings" and select "sensors" there is a blank screen. There is no "+" or add button or even any choices other than "back". I then tried to set it up under my own account. I clicked the "+" and there were choices to setup 1) irrigation controller, 2) Hose faucet Timer and 3)Shop Products.  Im  still looking for detailed instructions...

Hello,

I am upgrading from 6 to 12 zones controller.

Is there a way to move all the historical data and zone settings to the new device ?

Thank you

valvole hunter 24vac, netro non apre le valvole.

i collegamenti sono stati eseguiti come da istruzioni.

Quale può essere il problema?

Alimentatore 24v 1000ma e’ corretto?

This season when I put my whisperer back out to monitor my garden bed I looked on the app and no longer saw that device. So I went through the process to re-add it to my network and my Netro account and I get an error message stating that that serial number is already registered.  Anyone have any thoughts on how I can de-register and re-register this device?  Thanks

Hi

I use Netafin pressure compensated drip hose on all my beds and there doesn’t seem To be an irrigation type for that. Is it OK using the drip setting which seems to be for micro drippers. 

Thanks

Hi,

My netro has been working fine for the past many months.

Suddenly it stopped working and light blinks.

I try to configure the Wifi again and it states 

I am sure my 2.4 GHz network is available there as I have 2 other devices 10 Cm away from the netro and are working fine at 2.4GHz

I can confirm that in my Orbi Router.

Any ideas ?

Thank you

Carlos 

Hi,

I have the netro connected to one water source.

Now I am going to install a vertical garden with very low flow and I want the source of water to be a different one from the main source for the garden.

Is there a way I can connect it as an independent solenoide valve that doesn't need to have the master turned on ?

Thank you,

Carlos

hello, 

finally the Whisperer sensors are wonderful.  I installed the 3 sensors divided by zones, a single problem that I encountered is this: the sensor that I called Prato should group 4 zones because they are part of the same type of plant, instead it only groups 3 zones.  I need your help.  

Thanks

Andrea

buongiorno 

Volevo sapere cortesemente in Italia centrale  Roma che tipo di erba selezionare nelle zone.

Grazie 

M.

When i install the whisperer sensor i can’t choose a zone. The installation begin without possibilities to choose. 

how i can do please ?

I leave un France 

Best regards 

I need to install the Netro Sprite in a tool shed covered by tiles and closed only on three sides that I have in the garden (L 2mt, W 1.5mt, H 1.8mt).

I would like to know if, to protect it from humidity, dust and insects, I can install it in a box like this:

https://www.amazon.com/Fielect-Transparent-Switchboard-Distribution-115x90x50mm/dp/B07ZR2HN5B/ref=sr_1_17?dchild=1&keywords=transparent%2BDistribution%2Bbox&qid=1587458726&rnid=2941120011&s=hi&sr=1-17&th=1

and if this box can decrease the reception of the wifi signal.

Thank you,

Is there a maximum distance I can place the whisperer(s) in the garden. Largest distance it should cover is approx. 30 mtrs.

The sprite probably will be placed inside.

I was having difficulty getting a leakproof seal when attaching my Smart Hose Faucet Timer (Pixie-1) to my new faucet. I finally was able to tighten it tight enough not to leak, but after a week, it broke and popped off. It is probably under warranty, but is there somewhere I can buy a new connector and repair it myself?

Hi

Hi 

just received a Netro Sprite controller 12 sone without power adapter 

I am in Rome , Italy

We have 240 volts energy supply

what adapter have i to buy ?

thanks 

paolo 

I am trying to install my Netro Pixie and the vacuum breaker is blocking the filter on the Pixie. Any suggestions? 

Good afternoon. 

 I have problems because I don't recognize the wifi.  I'll explain. First I connect by wifi to netro and it does not give me any problems.  But when I go back to the next screen to connect the mobile to the wifi and the wifi from home no longer appears. He's gone. And I can't continue with the installation.

Regards

Hi good morning,

I’m making the first installation and I see the valves don’t open when I tested it, so I test the connections with a multi-meter and sometimes it gives 24v and sometimes 0.
The last 10 tries it gives 0. I changed the cables and I now I test directly the controller connections and keep giving me 0.
I’m using the manual watering to make the tests.
Is it working correctly?
Thank you for your help.