Hi Mark,

Could you please let us know on which day Netro App does show watering in real time?

Thanks,

Netro Support

Hi Alfonso,

Could you please send us email to support@netrohome.com with your Netro account registered email?

Dear customer,

Thanks for reporting this issue and I have forwarded it to our R&D. We are trying to reproduce this issue. Could you please let us know is your mobile phone and device in the same time zone?

Thanks,

Wency

Netro Support

Hi Sander,

We will set the minimum value to 1mm in the future release of the app and currently you can set it as 10mm.

Thanks,

Wency,

Netro Support

Hi Judith,

It is possible that the timer was shipped by airplanes and the shipping company may have demagnetize the internal valve. Manually turning on and off the valve (quickly press the button twice) for about 10 times can fix this issue.

Pleaase let us know if it works.

Thanks,

Wency

Netro Support

Hi David,

Could you please send us email to support@netrohome.com with your Netro account registered email?
We will have our technician look into this issue. 

Thanks
Wency
Netro Support

Dear customer, 

This might be a bug and we have enabled your device now. We will  fix this bug in the next version. Please do not check the battery level on the home page. 

Thanks, 

Wency 

Netro Support

Hi Anthony,

One Netro pixie timer only allows one sensor. 

Thanks,

Wency

Netro Support

Hi Gabriele,

We have also received your email. We will have our technician look into this issue and get back to you soon.

Thanks,

Wency

Netro Support

Hi John,

Here is the online digital manual https://www.netrohome.com/en/shop/help_center?category=video&serial=SPRITE

Thanks,

Wency

Netro Support

Hi Anthony,

We checked your device and it is in idle mode. This might be a bug and we have enabled your device now. Could you please try again to check the wifi status?

Thanks,

Wency

Netro Support

Hi Rob,

We found your device status is standby mode. Could you please enable your device to check if it works?

Thanks,

Wency

Netro Support

Dear customer,

For Spark you can setup a local backup program stored on-device which is nonvolatile. The backup program does not depend on the cloud server and will always run. 

Thanks,

Netro Support

Dear customer,

1.If there is no wifi when Netro is watering, Netro will still finish all watering schedules as long as there is power. Netro will send notification when the system is offline more than 24 hours.

2. Usually devices will automatically reconnect to the server immediately after power outage. Netro Spark controller has a backup program to run if it goes offline. Netro Sprite controller does not have the backup program.

3.The Whisperer sensor is sold separately and it is only available on our own website https://netrohome.com. 

Please let us know if you have any further questions.

Thanks,

Wency

Netro Support

Dear Vanina,

Please check the wires. Are they loose or disconnected from the slots? Please also check the common wires and the master valve if you have one. If you believe the wires are correctly installed,  please check if there is a main valve/faucet that is turned off manually. 

To test if the controller is working properly, use a multimeter (AC voltage mode) to test the voltage between the common wire and the zone wire when the zone is active. Normally the voltage should be between 24V and 28V.

You might also want to check whether there are shorted zones or open zones. You just need to use a multimeter to measure the resistance between the common wire and each zone (remove the wires from the slots before testing the resistance). The normal reading would be 20-60 Ohms. If the reading is less than 10 Ohms then you might have a shorted circuit in the solenoid and if it is larger than 80 Ohms you might have an open circuit. 

Thanks,

Wency

Netro Support

Hi Duane,

Could you please send us email to support@netrohome.com with your Netro account registered email?

We will have our technician look into this issue. 

Thanks

Wency

Netro Support

Hi Jose,

It is the battey issue. Could you please place the sensor under the sunlight for another 2-3 days to charge it up and see if it works?

Thanks,

Wency

Netro Support

Dear Quim,

The red flash means the unit has less than 10% power. The winter sunlight may not be very strong. 

Could you please place the sensor under the sunlight for another 2-3 days to charge it up? Also, Do you have an incandescent lamp at home? If so, you can try to put the sensor under the incandescent lamp for 24-48 hours and it may come back to work.

Thanks,

Wency

Netro Support

Hi Vieri,

Thanks for your suggestion and I will forward it to our R&D.

Thanks,

Wency

Netro Support

Hi August,

I will forward your request to our R&D. Netro also supports IFTTT and you can find more information about IFTTT here: https://www.netrohome.com/shop/user_guides/6

Thanks,

Wency

Netro Support