Hi, I have a Spark controller. Where can I find in the app the rainfall forecast for next days?

In the home page I can see only humidity, temperature and wind but not rain in mm.

Thanks

Riccardo

I can't register my weather station ID in the Netro app. Can anyone help me? Thanks.

I have a home weather station that feeds data to https://www.wunderground.com/dashboard/pws/KCASANJO507?cm_ven=localwx_pwsdash

I have my sprite pointed at my specific weather station on wundergound.com. Today, my sprite claims I had 0.02" of rain, but my weather station detected none, and wunderground.com says I had no rain.

I have been noticing for a while that Netro was showing different rain data from what my weather station recorded, Netro usually records more rain than I actually got. I suspect this may be why my oranges are always under sized.

Somehow Netro is getting the wrong infromation from wunderground.com. Is there any way to fix this?

Is it possible to configure the irrigation time with seconds? or should it always be minutes?

Hi, 

any update on the "greenhouse" options which would not count on with the rain, wind and probably increase the temperature for the selected zone?

Thanks!

I have changed the name of my Wi-Fi. I need to change my Wi-Fi connection to its new name I have a new Wi-Fi in your hub will not work because it can’t download a new Wi-Fi for some damn reason

I have changed the name of my Wi-Fi. I need to change my Wi-Fi connection to its new name I have a new Wi-Fi in your hub will not work because it can’t download a new Wi-Fi for some damn reason

I have changed the name of my Wi-Fi. I need to change my Wi-Fi connection to its new name

Hi- been using your sprinkler controller for several years and have recently added a new WiFi network. 

I'm following the instructions how to switch the Netro controller to a new WiFi network. After resetting the controller, it change my iphone WiFi network over to Netro-XXX (which tells me I have no internet access). 

When I return to the Netro app and click 'Next', it just keeps instructing me to connect to Netro-XXX first. 

The Netro controller continues to blink despite unplugging it so stuck in limbo now. 

Thank you

¿Como puedo hacer un riego manual zona a zona para comprobar lis goteros obstruidos?

I have a Netro Sprite (6 zones).

I would like to water one time a week, 4 hours per zone in one run. I am not able to make programmes and single runs longer than 60 minutes. 

Am I doing something wrong, or is this not supported?

Thanks for helping me out.

Hello! I would like to set up my system to skip watering if soil moisture reads above a certain threshold. I have the Whisperer and the Pixie, so would like the Whisperer to communicate with the Pixie, so the Pixie skips watering if soil moisture is high enough. Is this possible? Thanks for your help. 

When I have Whisperers, the system appears to calculate the average over the day about 4 degrees higher than for zones without Whisperers.

It seems that, even though the weather data is available throughout the day, that zones without sensors only use the forecast high and low.

This is insufficient to correctly adjust for the amount of watering required.

For example, today is 7 degrees C up to 36.

Whisperer zones average the temp at 26C while non-Whisperer zone calculate the average at 22C.

On these extremely hot days, the non-whisperer zones are under-watering much more than the Whisperer zones.

Also note that even the zones with Whisperers always under-water and needs custom programs or manual intervention.

This finally explains to me why zones are always under-watered.

Can the system please use multiple day readings for non-Whisperer zones and PLEASE provide more watering?

Hello,

I have 2 Whisperer for automatic regularion of my watering.

They work normally work perfekt but when the bad weather prevents charging for o longer period they go to sleep/closes down.

Then my Netro thinks the soil is dry 0% humidity and aut starts my watering eventhough the soil is 90%.

I have ti disable the Netro to stop watering until the Whispering is charged.

Since I do not get any warning that the Wispering power is too low the aut watering can go on and on wasting my water and flooding my garden!

I have one particular zone that i only require watering for 15 seconds every second day.

How can i do this?  i was able to do it on my previous OpenSprinkler.

My two whisperers stopped due to lack of sun. The new one started communicating again.

The old one started communicating but then stopped while the battery was still above 90%.

Seems a communication problem 

Blue light blinking turned quickly to white light blinking.

After blinking a few minutes it stopped but is not connected to the App.

Tried putting it ON close to controller and then close to WiFi router, the result is the same, no connection.

Is the whisperer dead ? Should I buy a new one ?

Thanks

My system keeps watering despite the fact that it is winter with snowy conditions. It schedule to follow city city restrictions. Why?

I just got a Whisperer 2 and it won’t charge past 90%. It’s been plugged in all day. Is the battery defective?

How do I connect my sensors to zones? I have the latest.

Is there a version of the app that runs on a Windows PC or a Raspberry Pi?

I run all my home automation on a dedicated Raspberry Pi so it would be nice to keep everything in one place.